Heat-induced morphological changes in silver nanowires deposited on a patterned silicon substrate

• Elyad Damerchi,
• Sven Oras,
• Edgars Butanovs,
• Allar Liivlaid,
• Mikk Antsov,
• Boris Polyakov,
• Annamarija Trausa,
• Veronika Zadin,
• Andreas Kyritsakis,
• Loïc Vidal,
• Karine Mougin,
• Siim Pikker and
• Sergei Vlassov

Beilstein J. Nanotechnol. 2024, 15, 435–446, doi:10.3762/bjnano.15.39

• the results from the scheme 1. Approximately one hour waiting time between cycles was chosen to give enough time for taking series of scanning electron microscopy (SEM, FEI, Nanosem 450) images after each heating cycle. Additionally, a separate series of transmission electron microscopy (TEM

Investigating ripple pattern formation and damage profiles in Si and Ge induced by 100 keV Ar⁺ ion beam: a comparative study

• Indra Sulania,
• Harpreet Sondhi,
• Tanuj Kumar,
• Sunil Ojha,
• G R Umapathy,
• Ambuj Mishra,
• Ambuj Tripathi,
• Richa Krishna,
• Devesh Kumar Avasthi and
• Yogendra Kumar Mishra

Beilstein J. Nanotechnol. 2024, 15, 367–375, doi:10.3762/bjnano.15.33

• microscopy (AFM) [3] and transmission electron microscopy (TEM), it is possible to visualize these features. Formation of dots, ripples, and pits have been well studied using IBS [4][5][6][7][8][9]. In the last few decades, numerous efforts have been made to understand IBS through simulations [10] as well as

• . The RBS measurements were performed in channelling mode using 2 MeV He+ ions at the PARAS facility at the Inter University Accelerator Centre (IUAC), New Delhi, and transmission electron microscopy (TEM) using an equipment from Jeol, Japan. The samples for TEM were prepared for cross-sectional studies

Comparative electron microscopy particle sizing of TiO₂ pigments: sample preparation and measurement

• Ralf Theissmann,
• Christopher Drury,
• Markus Rohe,
• Thomas Koch,
• Jochen Winkler and
• Petr Pikal

Beilstein J. Nanotechnol. 2024, 15, 317–332, doi:10.3762/bjnano.15.29

• could not be ruled out” [7]. Recently, papers have been published in which a number of E171 samples were found by transmission electron microscopy (TEM) to be nanomaterials according to the EU definition [8][9]. For TiO2 producers this is surprising as the former food-grade titanium dioxide E171 is

TEM sample preparation of lithographically patterned permalloy nanostructures on silicon nitride membranes

• Joshua Williams,
• Michael I. Faley,
• Joseph Vimal Vas,
• Peng-Han Lu and
• Rafal E. Dunin-Borkowski

Beilstein J. Nanotechnol. 2024, 15, 1–12, doi:10.3762/bjnano.15.1

• ], transmission electron microscopy (TEM) [1][8][9][10][11], scanning transmission X-ray microscopy [12][13], and magneto-optical Kerr effect microscopy [14][15]. Possible applications of Py nanodisks were proposed for zero-hysteresis magnet sensors, magnetic logic devices, and data storage [16]. Py is a nickel

Determination of the radii of coated and uncoated silicon AFM sharp tips using a height calibration standard grating and a nonlinear regression function

• Perawat Boonpuek and
• Jonathan R. Felts

Beilstein J. Nanotechnol. 2023, 14, 1200–1207, doi:10.3762/bjnano.14.99

• relation to the PSD were collected to observe the tip blunting behavior. The quantitative determination of the tip radii compared to transmission electron microscopy (TEM) images of the tips showed corresponding results between the blunted tips and the PSD curves, concluding that blunter tips produced a

Sulfur nanocomposites with insecticidal effect for the control of Bactericera cockerelli

• Lany S. Araujo-Yépez,
• Juan O. Tigrero-Salas,
• Vicente A. Delgado-Rodríguez,
• Vladimir A. Aguirre-Yela and
• Josué N. Villota-Méndez

Beilstein J. Nanotechnol. 2023, 14, 1106–1115, doi:10.3762/bjnano.14.91

• eucalyptus and rosemary at different concentrations. Characterizations were carried out through UV–visible spectroscopy, energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and scanning electron microscopy (SEM); also the insecticidal efficacy of the NCMPs for the control of

Isolation of cubic Si₃P₄ in the form of nanocrystals

• Polina K. Nikiforova,
• Sergei S. Bubenov,
• Vadim B. Platonov,
• Andrey S. Kumskov,
• Nikolay N. Kononov,
• Tatyana A. Kuznetsova and
• Sergey G. Dorofeev

Beilstein J. Nanotechnol. 2023, 14, 971–979, doi:10.3762/bjnano.14.80

• “WinXPow”. Elemental analysis was carried out on an X-ray fluorescence spectrometer S2 Picofox (Bruker) with total external reflection. Transmission electron microscopy (TEM) samples were dispersed in an ultrasonic bath with hexane and then deposited on copper grids with lacey carbon film (SPI Supplies

Upscaling the urea method synthesis of CoAl layered double hydroxides

• Camilo Jaramillo-Hernández,
• Víctor Oestreicher,
• Martín Mizrahi and
• Gonzalo Abellán

Beilstein J. Nanotechnol. 2023, 14, 927–938, doi:10.3762/bjnano.14.76

• CoAl-based LDH synthesis through an ARR method had been demonstrated, morphological aspects were addressed by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM) (Figure 4 and Figure 5). For reference x1, well-defined hexagonal single

• Gwyddion software was used for flattening and image correction. Transmission electron microscopy (TEM) Transmission electron microscopy was carried out using a JEOL JEM-1010 at 100 kV accelerating voltage and a Tecnai F20 operated at 200 kV. Images were acquired in bright-field mode with an objective

Green SPIONs as a novel highly selective treatment for leishmaniasis: an in vitro study against Leishmania amazonensis intracellular amastigotes

• Brunno R. F. Verçoza,
• Robson R. Bernardo,
• Luiz Augusto S. de Oliveira and
• Juliany C. F. Rodrigues

Beilstein J. Nanotechnol. 2023, 14, 893–903, doi:10.3762/bjnano.14.73

• , arrowheads). The ferrous nature of the observed structures was assessed by chemical element mapping analysis using energy-dispersive X-ray spectroscopy (Figure 2C), confirming that the electron-lucent structures contain iron atoms (Figure 2D). Transmission electron microscopy (TEM) was used to confirm the

Ultralow-energy amorphization of contaminated silicon samples investigated by molecular dynamics

• Grégoire R. N. Defoort-Levkov,
• Alan Bahm and
• Patrick Philipp

Beilstein J. Nanotechnol. 2023, 14, 834–849, doi:10.3762/bjnano.14.68

• substantially more controllable at low energies [10][11], which also makes such beams valid candidates for these processes. Another application includes lamella preparation for transmission electron microscopy (TEM). TEM and scanning electron microscopy (SEM) have high constraints regarding cleanliness [12

Nanostructured lipid carriers containing benznidazole: physicochemical, biopharmaceutical and cellular in vitro studies

• Giuliana Muraca,
• María Esperanza Ruiz,
• Rocío C. Gambaro,
• Sebastián Scioli-Montoto,
• María Laura Sbaraglini,
• Gisel Padula,
• José Sebastián Cisneros,
• Cecilia Yamil Chain,
• Vera A. Álvarez,
• Cristián Huck-Iriart,
• Guillermo R. Castro,
• María Belén Piñero,
• Matias Ildebrando Marchetto,
• Catalina Alba Soto,
• Germán A. Islan and
• Alan Talevi

Beilstein J. Nanotechnol. 2023, 14, 804–818, doi:10.3762/bjnano.14.66

• different types of nanoparticles and BNZ, including SLN and NLC [21]. The NLC-BNZ formulation was analyzed using transmission electron microscopy (TEM) to confirm the presence of nanoparticles showing a spherical morphology and a narrow distribution of sizes (Figure 1). Image analysis through ImageJ [22

Silver nanoparticles loaded on lactose/alginate: in situ synthesis, catalytic degradation, and pH-dependent antibacterial activity

• Nguyen Thi Thanh Tu,
• T. Lan-Anh Vo,
• T. Thu-Trang Ho,
• Kim-Phuong T. Dang,
• Van-Dung Le,
• Phan Nhat Minh,
• Chi-Hien Dang,
• Vinh-Thien Tran,
• Van-Su Dang,
• Tran Thi Kim Chi,
• Hieu Vu-Quang,
• Radek Fajgar,
• Thi-Lan-Huong Nguyen,
• Van-Dat Doan and
• Thanh-Danh Nguyen

Beilstein J. Nanotechnol. 2023, 14, 781–792, doi:10.3762/bjnano.14.64

• morphology of the nanocomposites was investigated using transmission electron microscopy (TEM) with a JEOL JEM-1400 instrument. Thermal analysis, including thermogravimetry analysis (TGA) and differential scanning calorimetry (DSC), was conducted using a LabSys Evo 1600 thermal analyzer (SETARAM, France

Carboxylic acids and light interact to affect nanoceria stability and dissolution in acidic aqueous environments

• Matthew L. Hancock,
• Eric A. Grulke and
• Robert A. Yokel

Beilstein J. Nanotechnol. 2023, 14, 762–780, doi:10.3762/bjnano.14.63

• representative of particle dissolution, due to the valence state change from Ce4+ to Ce3+ during dissolution. The particles in citric acid exposed to light were completely dissolved after four weeks as indicated by DLS and transmission electron microscopy (TEM), shown in Table 1 and Table 2, respectively. In

• transmission electron microscopy (TEM) imaging, samples were sonicated for 10 min in a sonication bath. Lacey carbon, 300 mesh, copper grids were dipped into the solution for approximately 5 s and dried overnight at room temperature. TEM was used to obtain images of particles throughout the experiment’s

Control of morphology and crystallinity of CNTs in flame synthesis with one-dimensional reaction zone

• Muhammad Hilmi Ibrahim,
• Norikhwan Hamzah,
• Mohd Zamri Mohd Yusop,
• Ni Luh Wulan Septiani and
• Mohd Fairus Mohd Yasin

Beilstein J. Nanotechnol. 2023, 14, 741–750, doi:10.3762/bjnano.14.61

• source, showed that different growth temperatures produce CNTs with similar crystallinity. In a study by Chong et al. [12], the combustion of propane in a premixed flame at varying equivalence ratios yielded similar effects on CNT growth, while transmission electron microscopy (TEM) analysis showed a

Titania nanoparticles for photocatalytic degradation of ethanol under simulated solar light

• Evghenii Goncearenco,
• Iuliana P. Morjan,
• Claudiu Teodor Fleaca,
• Florian Dumitrache,
• Elena Dutu,
• Monica Scarisoreanu,
• Valentin Serban Teodorescu,
• Alexandra Sandulescu,
• Crina Anastasescu and
• Ioan Balint

Beilstein J. Nanotechnol. 2023, 14, 616–630, doi:10.3762/bjnano.14.51

• diffraction (XRD) patterns, measured by an X-ray diffractometer Panalytical X’Pert MPD theta–theta, and the morphological properties were determined by transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and selected-area electron diffraction (SAED) measurements

On the use of Raman spectroscopy to characterize mass-produced graphene nanoplatelets

• Keith R. Paton,
• Konstantinos Despotelis,
• Naresh Kumar,
• Piers Turner and
• Andrew J. Pollard

Beilstein J. Nanotechnol. 2023, 14, 509–521, doi:10.3762/bjnano.14.42

• %), transmission electron microscopy (TEM) (7.2%) or X-ray photoelectron spectroscopy (XPS) (5.6%). It has the advantages of relatively low cost, simple sample preparation, quick measurements, and automated analysis, offering clear benefits for quality control applications. It has been demonstrated in several

Quercetin- and caffeic acid-functionalized chitosan-capped colloidal silver nanoparticles: one-pot synthesis, characterization, and anticancer and antibacterial activities

• Akif Hakan Kurt,
• Elif Berna Olutas,
• Fatma Avcioglu,
• Hamza Karakuş,
• Mehmet Ali Sungur,
• Cansu Kara Oztabag and
• Muhammet Yıldırım

Beilstein J. Nanotechnol. 2023, 14, 362–376, doi:10.3762/bjnano.14.31

• infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM). The characteristic surface plasmon resonance (SPR) absorption band has been found at 417 and 424 nm for Ch/Q- and Ch/CA-Ag NPs, respectively. The formation of a chitosan shell comprising quercetin and caffeic acid, which surround the

• of quercetin, caffeic acid, chitosan, Ch/Q-, and Ch/CA-Ag NPs were monitored using a Perkin Elmer Spectrum Two FTIR-ATR spectrophotometer in the range of 4000–400 cm−1. Transmission electron microscopy (TEM) measurements were performed with a JEOL JEM-2100 electron microscope operating at 200 kV

Structural, optical, and bioimaging characterization of carbon quantum dots solvothermally synthesized from o-phenylenediamine

• Zoran M. Marković,
• Milica D. Budimir,
• Martin Danko,
• Dušan D. Milivojević,
• Pavel Kubat,
• Danica Z. Zmejkoski,
• Vladimir B. Pavlović,
• Marija M. Mojsin,
• Milena J. Stevanović and
• Biljana M. Todorović Marković

Beilstein J. Nanotechnol. 2023, 14, 165–174, doi:10.3762/bjnano.14.17

• 2.2 mg/mL. These specimens were designated as CQDs/PU. For bioimaging studies, toluene was evaporated, and a thin film of CQDs was redissolved in water and filtered. The prepared QCD samples were characterized by transmission electron microscopy (TEM), atomic force microscopy (AFM), Fourier

Antimicrobial and mechanical properties of functionalized textile by nanoarchitectured photoinduced Ag@polymer coating

• Jessica Plé,
• Marine Dabert,
• Helene Lecoq,
• Sophie Hellé,
• Lydie Ploux and
• Lavinia Balan

Beilstein J. Nanotechnol. 2023, 14, 95–109, doi:10.3762/bjnano.14.11

• electron microscopy (SEM), transmission electron microscopy (TEM), and reflectance measurements to assess the optical properties and the durability of the functionalized textiles. Results and Discussion Photoinduced synthesis of the Ag@polymer coating Specific monomers poly(ethylene glycol) 600 diacrylate

• (Figure 4a) and Ag@PEG600DA/PETIA (Figure 4b) coatings, respectively. The AgNP size dispersion is also slightly higher in the case of Ag@PEG600DA. Both results are coherent with the peak and FMWH values calculated from the absorbance spectra (Figure 2c). Transmission electron microscopy (TEM) cross

• measurements. A Bio photometer UV–vis spectrometer from Eppendorf was used to assess bacteria and yeast suspensions by OD measurements at 600 nm. Surface characterizations were carried out using transmission electron microscopy (TEM) at 200 kV on a Philips CM200 instrument (LaB6 cathode) and scanning electron

Solvent-induced assembly of mono- and divalent silica nanoparticles

• Bin Liu,
• Etienne Duguet and
• Serge Ravaine

Beilstein J. Nanotechnol. 2023, 14, 52–60, doi:10.3762/bjnano.14.6

• shell of approx. 15 nm (as estimated by transmission electron microscopy, TEM). The latter is made up of covalently grafted PS macromolecules resulting from the copolymerization of styrene with methacryloxymethyl groups. As previously demonstrated [25], these PS chains can serve as sticky patches when

Two-step single-reactor synthesis of oleic acid- or undecylenic acid-stabilized magnetic nanoparticles by thermal decomposition

• Mykhailo Nahorniak,
• Pamela Pasetto,
• Jean-Marc Greneche,
• Volodymyr Samaryk,
• Sandy Auguste,
• Anthony Rousseau,
• Nataliya Nosova and
• Serhii Varvarenko

Beilstein J. Nanotechnol. 2023, 14, 11–22, doi:10.3762/bjnano.14.2

• be adsorbed on the surface of the particles, ensures nanodispersion stability (Figure 1) [31]. Transmission electron microscopy (TEM) micrographs of the prepared nanoparticles confirmed their size between 8 and 16 nm (Figure 2 and Figure 3). The diameter and shape of the nanoparticles depend on the

A TiO₂@MWCNTs nanocomposite photoanode for solar-driven water splitting

• Anh Quynh Huu Le,
• Ngoc Nhu Thi Nguyen,
• Hai Duy Tran,
• Van-Huy Nguyen and
• Le-Hai Tran

Beilstein J. Nanotechnol. 2022, 13, 1520–1530, doi:10.3762/bjnano.13.125

• nanocomposite characterizations The surface morphology of MWCNTs and the TiO2@MWCNTs nanocomposite is characterized by using field-emission scanning electron microscopy (FE-SEM, S4800) and transmission electron microscopy (TEM, JEOL-1400). The crystallization behavior of the catalysts is analyzed by X-ray

In search of cytotoxic selectivity on cancer cells with biogenically synthesized Ag/AgCl nanoparticles

• Mitzi J. Ramírez-Hernández,
• Mario Valera-Zaragoza,
• Omar Viñas-Bravo,
• Ariana A. Huerta-Heredia,
• Miguel A. Peña-Rico,
• Erick A. Juarez-Arellano,
• David Paniagua-Vega,
• Eduardo Ramírez-Vargas and
• Saúl Sánchez-Valdes

Beilstein J. Nanotechnol. 2022, 13, 1505–1519, doi:10.3762/bjnano.13.124

• -dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM) techniques were used to characterize nanoparticle development. The breast cancer cell line MCF-7 was used as a test model to study the cytotoxic behavior of Ag/AgCl nanoparticles and, as a counterpart, the nanoparticles were also

Enhanced electronic transport properties of Te roll-like nanostructures

• E. R. Viana,
• N. Cifuentes and
• J. C. González

Beilstein J. Nanotechnol. 2022, 13, 1284–1291, doi:10.3762/bjnano.13.106

• under mild conditions. A large quantity of these polycrystalline nanostructures with a diameter between 100 and 900 nm and a wall thickness around 50 nm were synthesized and characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy

• (TEM), and selected-area electron diffraction (SAED). Individual Te roll-like nanobelts were connected in back-gate FETs and measured to characterize the electronic transport as a function of temperature. Methods Growth of Te roll-like one-dimensional nanostructures Te nanostructures were grown via an

Spindle-like MIL101(Fe) decorated with Bi₂O₃ nanoparticles for enhanced degradation of chlortetracycline under visible-light irradiation

• Chen-chen Hao,
• Fang-yan Chen,
• Kun Bian,
• Yu-bin Tang and
• Wei-long Shi

Beilstein J. Nanotechnol. 2022, 13, 1038–1050, doi:10.3762/bjnano.13.91

• , FEI-quanta 200, Japan Electronics, Japan), transmission electron microscopy (TEM, FEI-Tecnai F20, USA) and high-resolution transmission electron microscopy (HRTEM, JEOL 2100F, Japan). The element valence and chemical composition was investigated using X-ray photoelectron spectroscopy (XPS, Axis ultra